| After-sales Service: | Reply Within 24 Hours |
|---|---|
| Warranty: | 2 Years |
| Structure: | Vertical |
| Shipping Cost: | Contact the supplier about freight and estimated delivery time. |
|---|
| Payment Methods: |
|
|---|---|
| Support payments in USD |
| Secure payments: | Every payment you make on Made-in-China.com is protected by the platform. |
|---|
| Refund policy: | Claim a refund if your order doesn't ship, is missing, or arrives with product issues. |
|---|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
| 1 | Discharge glove box |
| 2 | Main machine part of the press |
| 3 | Feeding and taking system |
| 4 | Powder weighing machine |
| 5 | Servo drive system of upper and lower guide plate |
| 6 | Magnetizing and demagnetizing system |
| 7 | Electric control system |
| 8 | Water chiller (Install on the machine) |
For :BDES-450/400KN all-electric magnetic field forming press
| Travel range of upper pressure head | 0-300mm |
| Travel range of lower pressure head | 0-250mm |
| Positioning accuracy of upper and lower sliders | ±0.01mm |
| Repeated positioning accuracy of upper and lower sliders | ±0.01mm |
| Demoulding method | The stress release type; After the stress is released, it will protect the demoulding under the constant holding pressure. |
| Holding pressure setting range | 50KG-2000KG |
| Demoulding stress rebound control accuracy | 0.01mm |
| Demoulding method | Adopt micro-rising rebound and holding pressure monitoring setting mode. |
| Stress springback time | 0.5~5 seconds,Manually set according to product conditions |
| Applicable Mould | W220mm*H180mm,Add powder height 150mm(MAX) |
| Cavity width 80mm(MAX),If there are special needs, it can be rised to 120mm | |
| Applicable products | Magnetization direction≤80mm,Free direction≤180mm,Pressure height≤80mm,Molding density≤4.2g/cm³,It can be used for some products that do not require isostatic pressing |
| Molding method | Bidirectional synchronous pressing or differential pressing can be Set. |
| Oxygen content control method | The flow balance mode of nitrogen inlet and outlet oxygen discharge, and the flow control mode adopts the combination of solenoid valve and glass flowmeter for automatic control |
| Orientation maximum magnetic field | ≥1.8T/80mm(In-cavity inspection, using magnetic side plate structure) |
| Basic size of press | 4075*3289*4359((Length * width * height)mm |
| Height of receiving port | 3553mm |
| Power of equipment(MAX) | 380VAC50HZ 120KW,average40KW |
| Circuit wiring | Three-phase five-wire, The signal line must be separately grounded,ground resistance≤4Ω |
| Air Pressure Request (N2): | Pressure:0.5~0.7MPa ,flux:1 M3 / min,Pipe diameter of access equipment:Rigid pipe diameter 3/4′,Diameter of flexiable hose≥φ16(Not more than 5 meters). |
| Cooling water requirements: | The coil must be cooled by a chiller separately, and the cooling water is required to use: deionized water or purified water,temperature:18<T≤22ºC,flux:≥5m³/h,Do not use ordinary water into the chiller. |
| Cooling water requirements for chillers: |
Water pressure0.1-0.3MPa,flux≥5m³/h |
| Use environment requirements: |
15-30ºC humidity is below 40%;(Users need to equip their own equipment to control temperature and humidity) |
1. We can provide production equipment for magnet materials .
2. We will customize the most suitable device for you according to your needs.
){kind=link}